ASTM D5519-2007 天然和人工粗石材料粒径分析标准试验方法

sigh007

                   【英文标准名称】:     Standard Test Methods for Particle Size Analysis of Natural and Man-Made Riprap Materials            【原文标准名称】:     天然和人工粗石材料粒径分析标准试验方法            【标准号】:     ASTM D5519-2007            【标准状态】:     现行            【国别】:                 【发布日期】:     2007    【实施或试行日期】: 【发布单位】: 美国材料与试验协会(US-ASTM)【起草单位】: D18.17【标准类型】: (Test Method)【标准水平】: ()【中文主题词】: 过滤器;分等级;人类;质量;粒子分析;粒度;粒径分析;尺寸;板层;土壤;试验【英文主题词】: armor stone;  filter bedding stone;  filter material;  gradation; riprap;  slab【摘要】: Riprap is commonly used to prevent erosion of underlying materials due to the effects of rain runoff, wind, flowing water, or wave action. The particle size distribution (mass of particles) is an important physical characteristic of riprap, as discussed in D 6825. These test methods provide a gradation of the material graphically represented as percent finer than the particle mass. If a gradation can be established or accepted on the basis of only maximum and minimum particle sizes, then it may not be necessary to establish the complete gradation in accordance with these test methods. These test methods can be used during evaluation of a potential source, as a means of product acceptance, or for assessment of existing installations. Method D is not recommended as a means of product acceptance. Other characteristics of interest, such as particle shape, particle angularity, or visually evident rock durability characteristics may be determined during the performance of these test methods. Interpretation of test results must consider the representativeness of the sample.  Note 28212;The agency performing these test methods can be evaluated in accordance with Practice D 3740. Not withstanding statements on precision and bias contained in these test methods: The precision of these test methods is dependent on the competence of the personnel performing it and the suitability of the equipment and facilities used. Agencies that meet the criteria of Practice D 3740 are generally considered capable of competent and objective testing. Users of these test methods are cautioned that compliance with Practice D 3740 does not in itself ensure reliable testing. Reliable testing depends on many factors; Practice D 3740 provides a means of evaluating some of those factors.1.1 These test methods cover the particle size and mass analysis of natural and man-made riprap and related materials, including filter stone or coarse bedding materials.1.2 These test methods are generally intended for riprap and related materials. They are applicable for mixtures of stones screened from natural deposits, blast rock, processed materials from quarried rock, or recycled concrete. They are applicable for sizes 3 in. (75 mm) and above, with the upper size limited only by equipment available for handling and weighing the individual particles.1.3 Four alternate procedures are provided. There is a wide range in the level of effort and the precision of the test procedures. It is important for specifiers to indicate the test procedure. Test reports should clearly indicate which procedure was used.Note 1While conducting these test methods, it may be convenient to collect data on other attributes, such as the amount of slab pieces and deleterious materials.1.4 All observed and calculated values shall conform to the guidelines for significant digits and rounding established in Practice D 60261.5 The values stated in inch-pound units are to be regarded as the standard. The metric equivalents of inch-pound units given in parentheses may be approximate.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific precautionary statements are given in Section 7.【中国标准分类号】: D50;A42【国际标准分类号】: 19_12【页数】: 10P.;A4【正文语种】:           
         

住在

？？？怎么下载啊阿萨斯飒飒的撒的撒的